79. The Wrong Pipe: Reconditioning A MADE IN EIRE 312 System

 I like to tell myself I’m not much of a pipe collector, but work on the Peterson book has forced me into the role more than I’d thought possible, all “for the greater good,” my Pipe Acquisition Disorder tells me. That being the case, during the course of writing and research on the Peterson book a number of interesting pipes have come my way. This MADE IN EIRE (in a circle) 312 Standard System is one of them. There are so many “wrong” things about this pipe that I thought you might find its story interesting.

When it arrived a few years back, at the beginning of our labors on the book, I was delighted because it was the first EIRE stamp I’d ever seen first-hand—EIRE being that very, very short period of Peterson history from 1938 – 1948.

Left to Right: Eire, Early Republic, Late Republic, Dublin Era 312s

The bowl, as you know if you looked at my last 312 blog, is something different from what is being frazed these days, a bit taller, a bit more egg-shaped, and just . . . different.* And that’s not what’s wrong with it—that’s all to the good for a Luddite like myself who usually prefers things as near to their sources as possible. Here’s what it looked like when I first did my reconditioning:

First Restoration

But to my taste, it smoked sourly and so I rarely pick it up. And for me that’s the first wrong thing—a pipe that gathers dust in the rack needs to find a home where someone is smoking it, or at least giving it some serious appreciation. I had restored the pipe to the best of my ability back when I received it, but in beginning to think about letting it go, I decided I’d have a second try at freshening it up, not wanting to sell someone second-rate goods.

So I gave it a 24-hr. dunk in an isopropyl bath, and it popped out smelling clean and sweet. That bit of wrongness, at least, was taken care of, as I proved to myself when I gave it a trial smoke at the end of the reconditioning.

After the alcohol soak, inasmuch as the wood is at the very least 70 years old, I thought I’d treat it to a coat of mineral oil, as Charles Lemon has demonstrated on his blog. I don’t think Charles leaves this on for more than 15-20 minutes, and certainly not all night, which I did. This wasn’t a mistake, exactly, but I don’t recommend it, for reasons I’ll explain later.  Anyway, the mineral oil did rejuvenate the wood and break out the grain, but it also re-darkened it and gave it a matte finish.

The black walnut stain is another “wrong” thing, albeit from a purely subjective standpoint, as it is unusual among the Peterson Systems I’ve seen. At first it was off-putting, as it obscured so much of the grain, and I’d hoped after the alcohol soak and clean-up I might be able to lighten the pipe a little which would make it more pleasing to me.

You can see that it’s not a bad piece of briar: some small minor fills, great birds eye on reverse side, but there is a major bald spot on the reverse above the stamp on the bowl (which I failed to photograph, but you get the picture). And that, I suspect, in combination with the 3 or 4 little fills, is what made it a Standard System, and what made giving it a black walnut stain the right thing to do.

Here’s the third bit of “wrongness.” The alcohol soak, as it often does, loosened the ferrule and so I took it off to have a look under the hood, so to speak. And take a look at it. It’s not nickel-soldered, it’s pressed! There’s no solder line on the outside or inside of the cup. “Wrong” is the incorrect word, of course. Surprising is more apt. You see, we know from the K&P Employee Register that K&P employed nickel-solderers for decades. And we (that’s my co-author Gary Malmberg and myself) had been thinking all along that all nickel mounts were hand-soldered in the factory before about 1961.

I went scurrying over to my rotation and pulled off the pre-1961 Standard Systems, and sure enough, some have that tell-tale solder-mark on the outside, others don’t. What’s the answer? I don’t know, but I do know the later pressed ferrules lacked the faux hallmarks (shamrock, wolf hound, round tower), and this one has them (although they’ve been almost eradicated by buffing), indicating that it was made prior to 1961, when the faux-marks were discontinued.

A fourth “wrong” that bothered me about this pipe: it’s a 312 Standard System, quite plainly marked, and the MADE IN EIRE stamp is supposed to mean it was made while Ireland officially knew itself as “Eire.” But during those years, a 312 was a second-grade pipe, not a third, and would have had a sterling mount, right? The shape number for a third grade (with nickel mount) was 362 in the 1937 catalog. In addition, it should have had a “3” stamped under PETERSON’S over SYSTEM on the obverse of the bowl, instead of STANDARD.

The explanation, of course, is that K&P abandoned the complicated second and third grade double numbering system sometime after 1937, but before the end of the Eire era in 1948. What I’d been thinking of as a “wrong” thing turns out to simply help date the pipe to sometime closer to the end of the era. At this point I began to get excited, having discovered something new about dating Petersons. There was also a bit of humility seeing in the rear view mirror another part of me, the guy who says, “Don’t tell me the facts; my mind’s made up.”

Replicating the 1937 Catalog Bend

A fifth, minor “wrong,” and one easily corrected, was simply that the mouthpiece looks like a replacement. The arch bend (which became more-or-less standard by the late 1980s) just didn’t ring true to the Eire era. After a few attempts with the heat gun and some dips in a bowl of cold water, I gave it a bend more typical of its era, seen in the 1937 catalog.

I followed the stem restoration with some final touches to the bowl, giving it a few coats of carnuba. Now, remember a moment ago when I talked about the mineral oil? When I smoked the pipe to check the bowl for sweetness, the oil pressed outward–I could see it visibly evaporate–necessitating a fresh coat of carnuba. I smoked it a second time just to be sure the mineral oil had dried, and it had.

Finally, of course, a pipe is simply “wrong” for the pipeman if he doesn’t appreciate it, which in my way of understanding (which is not everyone’s) means smoking it.

I did smoke it twice to assure myself it was sweet and clean, but after such a problematic relationship, and with other established 312s in the rack, I knew I’d never give it the attention it deserves: respect but not companionship, I suppose. So I gave it a final touch-up, cleaning out the mouthpiece again and giving the bowl a light cotton-pad and isopropyl treatment before putting it on the market. And as of this writing, I’m happy to report it has found a new home in Waco, Texas, where I understand it is being treated with the admiration it so richly deserves.

Rath Dé ort!

 

*FRAZING MACHINE: A machine which guides briar block against cutters to duplicate preselected pipe shape. A clamp-fitted shaft and a cam follows a master model to shape shank and lower half of bowl.

I haven’t been able to find a photograph of a frazing machine, but Pipedia gives us this additional information: “A frazing machine has been used in the manufacture of Pipes. Its general structure is such that a pattern of the pipe or pattern of a section of a pipe is mounted in the machine and then the stummel is installed in the same machine. When the frazing machine is started the pattern pre-installed in the machine is then recreated on the surface of the stummel. In other industries of modern methods of manufacture, they are referred to as pantograph machines and pattern makers. Some pipe makers do not use such machinery and rely on the person crafting the pipe as the three-dimensional view provided is believed to produce a more acceptable and aesthetic appearance. Such companies that do utilize frazing machines reserve them for ‘roughing in’ the stummel only when manufacturing multiple pipes of exactly the same style.”

 

0 0 votes
Article Rating
Subscribe
Notify of
guest

10 Comments
Oldest
Newest Most Voted
Inline Feedbacks
View all comments
upshallfan
upshallfan
6 years ago

I’ve had a few pipes saved with a last-ditch isopropyl dunk. Nice bend job on the stem!
It is surprising what an old pipe can teach you, if you look close enough!

Jørgen Jensen
Jørgen Jensen
6 years ago

This morning I started on a De Luxe 120 bought in Dublin in the 90ties.
Had I read this first I would have started on a 312 “O” with nickel band,Made in England,instead

Mark Irwin
Admin
6 years ago
Reply to  Jørgen Jensen

Two of my favorite Pete shapes, Jorgen!

rebornpipes
6 years ago

Reblogged this on rebornpipes and commented:
Mark has given us a good read on this one. Thought I would share it with the readers on rebornpipes. Thanks Mark.

Mark Irwin
Admin
6 years ago
Reply to  rebornpipes

Thanks, Steve! You’re “the Man” in my book.

Mark Irwin
Admin
6 years ago
Reply to  Mark Irwin

My dad sends this URL for a look at a frazing machine at the old Dr. Grabow factory:
http://www.flickr.com/photos/fastredx/5011040538

upshallfan
upshallfan
6 years ago
Reply to  Mark Irwin

Wow, I’d love a closer look at that machine, I’ve never seen one before.

Charles Lemon
6 years ago

Another entertaining and informative read, Mark. And you are bang on with the mineral oil. I apply it lightly with a cotton pad and let it sit for 15 minutes or so before removing the excess with a towel.

The pipe turned out very nicely. Glad to know it’s being used and appreciated!

James Arrington
James Arrington
6 years ago

Mark, thanks for the highly informative post. You did great work on this pipe and I’m very happy to have gotten it. I’m actually in Austin, but rest assured she has gotten a good home !

Mark Irwin
Admin
6 years ago

Austin! Sorry for that. Glad you like the pipe. It’s a fantastic piece.